Team10 temperature and humidity sensor

From Sketching with Hardware at LMU Wiki
Revision as of 10:42, 11 October 2022 by 138.246.3.127 (talk) (Specifications and setup of a BME680 sensor using the Wemos D1 Mini with Arduino.)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

BME680 Temperature, Humidity, Air Pressure & Gas Sensor

The BME680 is a sensor by BOSCH that can measure gas, preassure, humidity an temperature. It was especially developed for wearables making it small and its power consumption minimal. The sensor can be interfaced with I2C and SPI.

Technical Data

  • Size: 3mm x 3mm + 0,93mm
  • Temperature: -40... + 85°C - Accuracy: +-1°C
  • Humidity: 0 - 100% relative Humidity - Accuracy: +- 3%
  • Preassure: 300‒1100 hPa - Accuracy: +- 1 hPa
  • Gas sensor: outputs a direct index for air quality (IAQ) with range from 0 (Excellent air quality) to >351 (Extremely polluted)

Advantages and Disadvantages

Advantages

  • humidity and preassure can be handled independently
  • low power consumption (Average current consumptionfor humidity and temperature: 2.1 µA at 1 Hz)
  • small size (2,5mm x 2,5mm x 0,93mm)
  • possibility of adding preassure and gas measurements
  • context awareness (skin detection, room change detection)

Disadvantages

  • only small in size without breakout
  • library takes up more memory flash space than other similar sensors
  • you need to use the BOSCH libraries

Get it to work

We connected the Wemos D1 Mini ESP8266 with the BME680 using Arduino.

Parts list

  • Wemos D1 mini
  • BME680 Air Quality Sensor breakout board
  • 4 connecting wires

Software

  • Arduino IDE
  • Adafruit BME680 library
  • Adafruit Unified Sensor Library

Schematic

  • Connect the Ground Pin of the BME680 to the Ground Pin of the Wemos D1 Mini
  • Connect the SCL Pin of the BME680 to D1 on the Wemos D1 Mini
  • Connect the SDA Pin of the BME680 to D2 on the Wemos D1 Mini
  • Connect the SCL Pin of the BME680 to D1 on the Wemos D1 Mini

Code example

 1 #include <Wire.h>
 2 #include <SPI.h>
 3 #include <Adafruit_Sensor.h>
 4 #include "Adafruit_BME680.h"
 5  
 6  
 7 #define SEALEVELPRESSURE_HPA (1013.25)
 8  
 9 Adafruit_BME680 bme; // I2C
10  
11 void setup() {
12   Serial.begin(115200);
13   while (!Serial);
14   Serial.println(F("BME680 test"));
15  
16   if (!bme.begin(0x76)) 
17   {
18     Serial.println("Could not find a valid BME680 sensor, check wiring!");
19     while (1);
20   }
21  
22   // Set up oversampling and filter initialization
23   bme.setTemperatureOversampling(BME680_OS_8X);
24   bme.setHumidityOversampling(BME680_OS_2X);
25   bme.setPressureOversampling(BME680_OS_4X);
26   bme.setIIRFilterSize(BME680_FILTER_SIZE_3);
27   bme.setGasHeater(320, 150); // 320*C for 150 ms
28 }
29  
30 void loop() 
31 {
32   if (! bme.performReading()) 
33   {
34     Serial.println("Failed to perform reading :(");
35     return;
36   }
37   Serial.print("Temperature = ");
38   Serial.print(bme.temperature);
39   Serial.println(" *C");
40  
41   Serial.print("Pressure = ");
42   Serial.print(bme.pressure / 100.0);
43   Serial.println(" hPa");
44  
45   Serial.print("Humidity = ");
46   Serial.print(bme.humidity);
47   Serial.println(" %");
48  
49   Serial.print("Gas = ");
50   Serial.print(bme.gas_resistance / 1000.0);
51   Serial.println(" KOhms");
52  
53   Serial.print("Approx. Altitude = ");
54   Serial.print(bme.readAltitude(SEALEVELPRESSURE_HPA));
55   Serial.println(" m");
56  
57   Serial.println();
58   delay(2000);
59 }

Instructional video

coming soon