Editing NEO-6M

= NEO-6M GPS with a high-gain patch antenna = 
The NEO-6M is a GPS module consists of the GPS chip which is the heart of this module and an antenna required for any kind of communication. This GPS-Module can track up to 5 location updates per second with 2.5m position accuracy. What makes the NEO-6M very suitable for smartwatches is the Power Save Mode, which reduces the power consumption to just 11 mA. 

== Technical Specifications ==
The NEO-6M GPS is an I2C sensor, which means that the usage of the clock/data wires is possible, and it can share these pins on the microcontroller with other sensors. In the following are some more specification to gain more technical insides. 

* Tracking: 22 satellites on 50 channels 
* Horizontal position accuracy: 2.5m
* Serial baud rate: 4800-230400 (default 9600)
* Operating range: -40 to 85°C
* Operating voltage: 3.3V – 5V 

The antenna is important for this module and handles any kind of communication. It is a high-gain patch antenna with a sensitivity of -161 dBm. It can be connected to the chip via an IPEX connector, which means it is an easy snap-fit on the module. 

The NEO-6M GPS module has an LED which gives information about the fix position. The LED blinks differently based on the state of the module. No blinking means the module is searching for satellites. If the LED is blinking every second, it means the chip can see enough satellites and has found a Position Fix.

=== Pinout ===
* '''VCC''' - power pin for the GPS module which can take 3-5V DC
* '''TX''' - transmission pin for serial communication 
* '''RX''' - receiver pin for serial communication
* '''GND'''

== Advantages and Disadvantages ==
=== Advantages ===
* Very little power consumption
* 23mm x 30mm dimension – usable for smartwatches
* Highest level of sensitivity 
* Tracking of 5 locations per second

=== Disadvantages === 
* Relatively large antenna
* Takes a while to find satellites in closed rooms

= How to get it to work =
To get this module started you first must solder the delivered pins on the GPS module, if it is not already done. After doing so, the wiring with the Raspberry Pi Pico can start. To get the NEO-6M GPS started, there are no other libraries necessary. 

== Wiring with Raspberry Pi Pico == 

{| class="wikitable" style="margin:auto"
|-
! NEO-6M GPS Module !! Raspberry Pi Pico
|-
| GND || GND
|-
| TX || GP4 (Pin6) - UART1 TX
|-
| RX || GP5 (Pin 7) - UART1 RX (not necessary to wire) 
|-
| VCC || VCC (Pin 36)
|}

== Code Example == 
<syntaxhighlight lang="python" line='line'>#import relevant modules
from machine import Pin, UART, I2C
import utime, time

#GPS Module UART Connection
gps_module = UART(1, baudrate=9600, tx=Pin(4), rx=Pin(5))
print(gps_module)

#Used to Store NMEA Sentences
buff = bytearray(255)

TIMEOUT = False

#store the status of satellite is fixed or not
FIX_STATUS = False

#Store gps coordinates
latitude = ""
longitude = ""
satellites = ""
gpsTime = ""

#get gps coordinates
def getPositionData(gps_module):
    global FIX_STATUS, TIMEOUT, latitude, longitude, satellites, gpsTime
    
    #run while loop to get gps data
    #or terminate while loop after 5 seconds timeout
    timeout = time.time() + 8   # 8 seconds from now
    while True:
        gps_module.readline()
        buff = str(gps_module.readline())
        parts = buff.split(',')
        
        #if no gps displayed remove "and len(parts) == 15" from below if condition
        if (parts[0] == "b'$GPGGA" and len(parts) == 15):
            if(parts[1] and parts[2] and parts[3] and parts[4] and parts[5] and parts[6] and parts[7]):
                
                latitude = convertToDigree(parts[2])
                # parts[3] contain 'N' or 'S'
                if (parts[3] == 'S'):
                    latitude = -latitude
                longitude = convertToDigree(parts[4])
                # parts[5] contain 'E' or 'W'
                if (parts[5] == 'W'):
                    longitude = -longitude
                satellites = parts[7]
                gpsTime = parts[1][0:2] + ":" + parts[1][2:4] + ":" + parts[1][4:6]
                FIX_STATUS = True
                break
                
        if (time.time() > timeout):
            TIMEOUT = True
            break
        utime.sleep_ms(500)
        
#convert raw Latitude and Longitude to actual Latitude and Longitude
def convertToDigree(RawDegrees):
    RawAsFloat = float(RawDegrees)
    firstdigits = int(RawAsFloat/100) #degrees
    nexttwodigits = RawAsFloat - float(firstdigits*100) #minutes
    
    Converted = float(firstdigits + nexttwodigits/60.0)
    Converted = '{0:.6f}'.format(Converted) # to 6 decimal places
    return str(Converted)
    
    
while True:
    getPositionData(gps_module)

    #if gps data is found then print it on lcd
    if(FIX_STATUS == True):
        print("Printing GPS data...")
        print(" ")
        print("Latitude: "+latitude)
        print("Longitude: "+longitude)
        print("Satellites: " +satellites)
        print("Time: "+gpsTime)
        print("----------------------")
        
        FIX_STATUS = False
        
    if(TIMEOUT == True):
        print("Request Timeout: No GPS data is found.")
        TIMEOUT = False

</syntaxhighlight>

== Instruction Video == 
Uploaded to Uni2Work
Latest revision		Your text
Line 1:		Line 1:
		+	= NEO-6M GPS with a high-gain patch antenna =
	The NEO-6M is a GPS module consists of the GPS chip which is the heart of this module and an antenna required for any kind of communication. This GPS-Module can track up to 5 location updates per second with 2.5m position accuracy. What makes the NEO-6M very suitable for smartwatches is the Power Save Mode, which reduces the power consumption to just 11 mA.		The NEO-6M is a GPS module consists of the GPS chip which is the heart of this module and an antenna required for any kind of communication. This GPS-Module can track up to 5 location updates per second with 2.5m position accuracy. What makes the NEO-6M very suitable for smartwatches is the Power Save Mode, which reduces the power consumption to just 11 mA.